A Hydraulic Wire Saw is a cutting machine that uses a diamond-coated wire to cut through reinforced concrete, bridges, and thick walls. It runs on hydraulic power with low vibration and low noise. This article shares a real sale of a Hydraulic Wire Saw to Singapore. A local demolition contractor bought the machine for a building removal project near offices and homes. The project needed quiet and safe cutting. This case shows how the right wire saw cutting machine helped finish the job without complaints.
Hydraulic Wire Saw Key Parameters
The YG hydraulic wire saw comes with the technical specs shown below. All numbers come from the factory documents.
| Parameter | Value |
| Motor Type | HM-40/80 (single/twin cylinder) |
| Minimum Input Power | 25/33 HP |
| Shaft Output Speed | 350/940/1300 r/min |
| Max Wire Length | 18 meters |
| Feed Mode | Fully automatic hydraulic |
| Cutting Machine Weight | 64 kg |
| Host Drive Motor Weight | 14 kg |
| Hydraulic Pump Station Power | 22/25 kW |
| Working Voltage | 380V 50Hz |
| Pump Station Type | Gear pump |
| Main Drive Motor Flow | 40-100 L/min |
| Working Pressure | 15-20 MPa |
| Fuel Tank Volume | 17 L |
| Pump Station Weight | 98 kg |
| Pump Station Size | 650×550×1150 mm |
The total machine weight is about 176 kg. A forklift can move the pump station around the job site. A stacker can lift the cutting head to higher positions when working on tall columns.
Concrete Wire Saw For Sale: Singapore Project Background
Singapore has very strict rules for demolition work. The Building and Construction Authority (BCA) requires low vibration and low noise. The customer was a local demolition contractor hired to remove an old building in a busy area.
The project situation:
The building had thick concrete columns with high-density steel bars
The job site sat next to a working office and a residential block
Strong shaking or loud noise would break the National Environment Agency (NEA) rules
The contractor had to finish within a tight 12-day schedule
The customer’s real needs:
A machine that could cut deep concrete without shaking the ground
Low noise so neighbors would not complain
Less labor needed because Singapore has high worker costs
The machine had to follow SS 557:2026 safety rules for demolition
A Concrete Wire Saw for sale needed to meet all these points.
Why The Customer Chose Hydraulic Diamond Wire Saw Specifications？
The customer did not just buy from the first seller. He compared several machines before making a decision.
How he compared different machines:
- Looked at hydraulic diamond wire saw specifications from three different brands
- Checked each machine’s motor power, wire length, and oil tank size
- Asked about the noise level during cutting
- Read the safety manuals to see if one worker could run the machine alone
What made him choose the YG machine？
The 18-meter max wire length could cut through the thickest columns in one setup
The fully automatic hydraulic feed gave steady power without stalling
The cutting machine unit weighed only 64 kg, so one person could move it
The pump station’s 22/25 kW power was strong enough for high-density steel
The price was fair for the power and build quality
The supplier also included a forklift and stacker in the same shipment for moving cut concrete blocks.
Wire Saw Cutting Machine Benefits
The YG wire saw cutting machine directly solved the customer’s main pain points: not tiring workers and saving labor costs.
How the machine made work less tiring for workers？
- The hydraulic system ran with very low vibration, so operators did not get tired hands
- The remote control let the worker stand far from the cutting area, away from dust
- The fully automatic hydraulic feed did all the pulling work; no heavy pushing needed
- The diamond wire cut cleanly without large concrete chunks flying around
How the machine saved labor costs？
- One trained worker could run the whole cutting job by himself
- No need for a large crew to break up concrete with hammers
- The clean cut surface did not need extra smoothing or repair work
- The machine ran for long hours without overheating, so the job finished faster
Other benefits for the Singapore site:
Low vibration met the BCA’s safety rules for demolition near standing buildings
Wet cutting kept dust down, following NEA waste rules
The forklift moved cut concrete pieces away quickly, and the stacker stacked them neatly for truck loading
Delivery And Real Customer Feedback
The YG hydraulic wire saw was shipped by sea freight to Singapore. All parts came in strong wooden crates with a full English manual and a video guide. The customer set up the machine on site in one morning.
What the customer reported after using the machine？
Cutting went much faster than his old hammer method
No one from the nearby buildings complained about noise or shaking
The machine did not overheat even after running all day
Only one worker was needed for the whole cutting job
The forklift moved the cut concrete sections to the disposal area with no delays
The stacker helped stack removed blocks in a safe pile for later truck loading
The customer said he would buy another machine for his next project
The project finished two days ahead of schedule. The contractor saved money on labor and avoided any fines from noise complaints.
FAQs About Hydraulic Wire Saw
Q1: How thick of concrete can this machine cut?
There is no limit. The only limit is the wire length, which goes up to 18 meters. The machine can cut any thickness.
Q2: Does the machine make loud noise?
No. The hydraulic wire saw runs much quieter than a hammer or breaker. It meets Singapore’s noise rules for demolition near homes and offices.
Q3: How many workers are needed to run the saw?
One trained worker can run the whole machine by himself. The lightweight cutting head (64 kg) and remote control make this possible.
Q4: Can the wire saw cut through steel bars inside concrete?
Yes. The diamond wire cuts through both concrete and steel reinforcement without stopping.
Q5: Does YG provide training for the machine?
Yes. YG gives a full English manual and a video guide with every machine. You can also ask for live video support.
Why Buy A Hydraulic Wire Saw From YG Company？
YG Company builds construction machinery with strong technical support and years of real factory experience. The hydraulic wire saw comes with a powerful 22/25 kW pump station, a lightweight 64 kg cutting head, and fully automatic hydraulic feed for easy one-man operation. YG provides clear English manuals, video training, and fast shipping to Singapore and other Asian countries. The company focuses on making machines that save labor, reduce noise, and cut straight. Unlike cheap brands, YG uses reliable hydraulic parts that last through tough demolition jobs. When you buy from YG, you get a product that works hard every day without breaking down. YG also offers full support for forklift and stacker integration, so your whole demolition workflow runs smoothly. Choose YG for equipment that makes demolition easy, safe, and profitable.